12 easy ways to use a chainsaw–a beginner guide

His chainsaw is an effective tool, but it can also be dangerous if used incorrectly. If it is the first time to use a chainsaw, please make sure to read its instruction manual thoroughly. It's also a good idea to practice using the tool on a small tree stump or log before attempting other more serious tasks. Here are some simple ways to use a chainsaw:  www.uanbuy.com

1. Safety first

In order to use the chainsaw safely, you must wear a helmet with a sun visor or use goggles. Also wear sturdy shoes and pants protected by a band saw. Bring a whistle or mobile phone in case you need it.

2. Take time to understand the saw

Take some time to get familiar with the chainsaw. Each chain saw is equipped with a chain catcher, throttle lock and stop control device. Other protective safety features of the saw include right-hand protection and recoil protection. These functions are all to prevent the saw from accidentally moving or the chain in the saw from breaking or derailing and stopping the saw.

3. Check the saw chain

It is a good idea to change the chain every few years. Before you start, make sure that the chain is properly tensioned. After a short period of operation, you need to re-tension the new chain.

4. Refuel to the best level

Always use environmentally friendly fuel and vegetable chain oil. While adding oil to the saw, place it on a flat surface. After refueling and before use, be sure to move the saw slightly to avoid fire.

5.Keep a safe distance

When using a chain saw, keep a safe distance of at least 5 meters from objects or living things. If you are cutting down trees, make sure that there are no people or animals around.

6. Tips for starting the saw

Before you start, place the saw on a flat surface.

You can activate the recoil protection, otherwise the chain will start to spin. Some saws also have a smart start decompression function. If you use, please use this feature. https://uanbuy.com

If the engine is cold, pull it out completely.

You can put your right foot in the rear handle and your left hand can hold the front handle firmly. Press the choke. Continue to pull the saw handle until the tool starts. After the saw is started, step on the accelerator to reduce the engine speed to idling.

7. Make sure the chain brake is working

Before using the saw before starting the saw, make sure that the chain brake is working properly. Squeeze the throttle while using recoil protection. Make sure that the chain stops immediately.

8. Check lubrication

To check the lubrication of the chain, place the saw on a shiny surface. Step on the accelerator and see if there is oil on the surface.

9. Tips for fixing the chainsaw correctly

There is a way to hold the saw correctly.

Always hold the two handles of the tool firmly. (Place your thumb and fingers on the two handles).

To reduce the possible recoil, hold the thumb of your left hand firmly under the left handle.

Always maintain proper balance when the saw is kept close to the body, but also respect it. However, you don't have to worry about sawing. When you bring the saw closer to your body, you will have more control over it.

When using a saw, always stand with your feet apart for better balance. The upper and lower edges of the saw chain.

10. Protect your back

Bend your knees, especially when doing low-level work. This can save you time.

11. Steps to fell trees

Before felling trees, please understand environmental regulations.

Do not work in adverse weather conditions such as heavy rain, strong wind or heavy snow.

Determine where the tree fell; make sure there are no animals, objects or people nearby. Clear obstacles under and around the tree.

Make sure that you can safely retreat when the tree starts to fall.

Consider factors such as wind direction, which determine the direction in which the tree falls.

Now you can start branching the tree at a convenient height that does not exceed shoulder height.

Cut the stem into the top at a 60 degree angle.

Saw to a depth of 20% to 25% of the diameter of the tree. After this, perform a horizontal cut to accommodate the previous cut. Finally, you need to make a horizontal cut, called a hinge, slightly higher than the undercut height

12. Spend time on the maintenance of the chainsaw

After using the saw, take some time for maintenance. This will ensure that it functions normally the next time you use it.

Run in chain stores from time to time.

Remove the clutch cover and clean the chain brake band.

You also need to clean the heat sink and air intake regularly.

Make sure that the sprocket drive is not too worn.

Tighten screws, nuts and bolts from time to time.

When the longest part of the cutting teeth seems to be worn or less than 4mm, replace the chain.